Lockeyusa M210 EZDC Bedienungsanleitung PDF herunterladen

Step 5: Adjust Deadbolt (if necessary) & Install

1. Adjustable Deadbolt (#12) is preset to 2 3/8”.

To adjust, lift pin and slide to 2 3/4”.

2. With arrow pointed UP, insert Deadbolt

and secure with two (2) Wood Screws (#11).

No.

Part Name

M210

M210 EZ

Outside Body

Inside Body

Rubber Trim Plate

Mortised Strike

Spindle 40-55 mm.

Spindle 30-45mm.

Machine Screw M4 x 50 mm.

Machine Screw M4 x 35 mm.

Wood Screw M4

Extra Code Tumblers (Red)

Extra Non-Code Tumblers (Blue)

Adjustable Deadbolt 2 3/8” – 2 3/4”

Tweezers

Hex Bolts

Brass Support Pin

EZ-Plates-M210 EZ (Not Shown)

Door Edge

Step 7: Install the Lockey M210

5. Place the Rubber Trim Plate (#3) on the

backside of the Outside Body (#1).

6. Place the Outside Body

on the door. The hexagonal

bolts (#14) should extend

into the top and bottom holes.

7. The Support Pin (#15) on the Inside

Body should fit into and extend through

the hole in the Deadbolt (#12).

INSTRUCTIONS CONTINUED ON REVERSE SIDE

Step 6: Verify Correct Spindle Length

1. With deadbolt (#12) installed, hold

the Inside Body (#2) and Rubber Trim

Plate (#3) to the door.

2. Place Spindle (#5/6) through Deadbolt,

into the Inside Body, as far as possible.

3. Spindle should extend from exterior of door

3/8” min. – 5/8” max.

4. If the 30-45 mm (#6) is too long, cut it to the correct length.

IMPORTANT: If spindle extends less than 3/8” it may not engage the lock. If spindle

extends more than 5/8”, it will cause the lock to bind.

Step 4: Install Support Pin & Hex Bolts

Install Brass Support Pin (#15) into either hole

on Inside Body as shown in the figure to

the Right [Left].

Install/screw Hex Bolts (#14) into the top

and bottom of the Outside Body

as shown in the figure (Far Right).

Step 3: Identify Door Handing

Right-Hand Doors – From exterior of

door, hinges are on right-side. (Fig. 1)

Left-Hand Doors – From exterior of

door, hinges are on left-side. (Fig. 2)

The M210 is factory pre-handed for

right-hand doors. To change handing, remove two

blue screws and cover plate from Outside Body.

Now, move the pin from the right side of the

outside body to the hole on the left side. Replace

plate and screws.

*M210 DC – Inside Body handing pin must be

placed on opposite side from Outside Body.

Lockey M-210 Deadbolt

Installation Instructions

Step 2: Prep Door for Installation with Template

1. Place template (supplied) on door and fold along door’s edge.

2. Mark holes for 2 3/8” or 2 3/4” backset.

3. Drill holes as instructed.

NOTE: For Pre-Prepped 2 1/8” doors, you only need to drill top hole.

Inside Body (#2)

Spindle (#5/6)

3/8” to 5/8”

Step 1: Change User Code (OPTIONAL)

If you wish to change your code, see instructions on reverse side.

FOR M210 EZ Instructions, turn to reverse side.

Thumb-Turn

M210 | M210 EZ | M210 DC | M210 EZ DC

Inside Body

Outside Body

Adj. Pin

2 3/8”

2 3/4”

1 2

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Step 5: Adjust Deadbolt (if necessary) & Install 1. Adjustable Deadbolt (#12) is preset to 2 3/8”. To adjust, lift pin and slide to 2 3/4”. 2.

Seite 2 - How to Change Code

M210 EZ Installation Instructions The M210 EZ is designed for doors with standard 2 1/8” prep 1. Determine door handing. Refer to Step #3 on reverse

Verwandte Modelle: M210 EZ | M210 DC | M210 |

Kommentare zu diesen Handbüchern

Keine Kommentare

Lockeyusa M210 EZDC Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sicherheit Lockeyusa M210 EZDC herunter. LockeyUSA M210 EZDC User Manual [en] [de] Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: M210 EZ | M210 DC | M210 |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheit Lockeyusa M210 EZDC