Lockeyusa M230 DC Bedienungsanleitung PDF herunterladen

Step 5: Verify Correct Spindle Length

1. With latch (#13) installed, hold

the Inside Body (#2) and Rubber Trim

Plate (#3) to the door.

2. Place Spindle (#6/7) through latch, into

the Inside Body, as far as possible.

3. Spindle should extend from exterior of door

3/8” min. – 5/8” max.

4. If the 30-45 mm (#7) is too long, cut it to the correct length.

IMPORTANT: If spindle extends less than 3/8” it may not engage the lock. If spindle

extends more than 5/8”, it will cause the lock to bind.

Step 6: Determine Knob Turn Direction (to unlock)

The lock is preset to unlock when turned clockwise after combination is

entered.

If desired, you can unlock the door with a

counter-clockwise turn. Remove the two

blue screws and move the pin to the

opposite side as shown.

*M230 DC – Inside Body pin must on opposite side from Outside Body.

No.

Part Name

M230

Outside Body

Inside Body

Rubber Trim Plate

Mortised Strike

Strike Plate

Spindle 40-55 mm.

Spindle 30-45mm.

Machine Screw M4 x 50 mm.

Machine Screw M4 x 35 mm.

Wood Screw M4

Extra Code Tumblers (Red)

Extra Non-Code Tumblers (Blue)

Adjustable Latch 2 3/8” – 2 3/4”

Tweezers

Hex Bolts

Brass Support Pin

Door Edge

Step 7: Install the Lockey M230

1. Place the Rubber Trim Plate (#3) on the

backside of the Outside Body (#1).

2. Place the Outside Body

on the door. The hexagonal

bolts (#15) should extend

into the top and bottom holes.

3. The Support Pin (#16) on the Inside

Body should fit into and extend through

the hole in the Latch (#13).

INSTRUCTIONS CONTINUED ON REVERSE SIDE

Step 4: Install Support Pin & Hex Bolts

Install Brass Support Pin (#16) into Inside

Body as shown in the figure to the

Right [Left].

Install/screw Hex Bolts (#15) into the top

and bottom of the Outside Body

as shown in the figure [Far Right].

Step 3: Adjust Latch (if necessary) & Install

1. Adjustable latch (#13) is factory preset for a 2 3/8” backset.

2. For 2 3/4” backsets, slide the Cam assembly on the latch to 2 3/4”.

3. Insert latch into door and secure with Wood Screws (#10).

Lockey M-230 | M230 DC

Installation Instructions

Step 2: Prep Door for Installation with Template

1. Place template (supplied) on door and fold along door’s edge.

2. Mark holes for 2 3/8” or 2 3/4” backset.

3. Drill holes as instructed.

NOTE: For Pre-Prepped 2 1/8” doors, you only need to drill top hole.

Inside Body (#2)

Spindle (#5/6)

3/8” to 5/8”

Step 1: Change User Code (OPTIONAL)

If you wish to change your code, see instructions on reverse side.

Thumb-Turn

Inside Body

Outside Body

2 3/8”

2 3/4”

1 2

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Step 5: Verify Correct Spindle Length 1. With latch (#13) installed, hold the Inside Body (#2) and Rubber Trim Plate (#3) to the door. 2. Place Sp

Seite 2 - How to Change Code

Step 7 cont: Install the Lockey M230 1. Insert the Spindle (#6/7) into the Outside Body (#1) ensuring it’s in the proper angled position. *(SEE F

Verwandte Modelle: M230

Kommentare zu diesen Handbüchern

Keine Kommentare

Lockeyusa M230 DC Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sicherheit Lockeyusa M230 DC herunter. LockeyUSA M230 DC User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: M230

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheit Lockeyusa M230 DC